It’s time to try this Orico high -value display support

Many office workers who often sit in the computer for a long time have some or less cervical spine problems. The reason why this happens is that most of the reasons are the height of the display. The more comfortable screen viewing angle, but in this way, it will cause a certain pressure on the cervical spine area. In the long run, there will be various discomforts. Because of this, many people currently like to put a bracket under the display, so that it can have the effect of raising the sight, and the cervical spine will be more comfortable. The orcio display bracket described in this article is a good choice.

不做低头族,是时候试试这款ORICO高颜值显示器支架了

Orico’s model of HSQ uses a very simple design style. It is stylish but not fancy. Both home and business scenarios are relatively good. At present, this monitor bracket has two versions of wood quality and aluminum alloy models, and each version has two colors. This article introduces the use of the gray aluminum alloy version.

不做低头族,是时候试试这款ORICO高颜值显示器支架了

ORICO’s bracket uses the assembly design. When the two brackets and bracket panels were just received, the screws and screw knives were equipped in the packaging. Together, the whole process took two minutes.

不做低头族,是时候试试这款ORICO高颜值显示器支架了

If it is on support, the wooden panel version can actually provide very good support effects, and the price is lower, which is a better choice for people who are pursuing cost -effectiveness. If you have high quality requirements for face value, there is no doubt that the aluminum alloy version can better meet your needs. The aluminum alloy version not only has the advantages of high hardness and wear, but also has a good texture. The panel adopts a thickened design. The surface is treated with delicate matte process. It soon disappeared.

不做低头族,是时候试试这款ORICO高颜值显示器支架了

The installation of the bracket foot is very simple. After the position is aimed at the position, just twist the screws in. The difficulty coefficient is basically zero. You can easily get it without reading the instructions.

不做低头族,是时候试试这款ORICO高颜值显示器支架了

Both aluminum alloy panels or bracket feet are relatively good. The edge area transitions is round. Basically, there is no handover. There is no burr in the corner area of ​​the bracket toes. The quality is still very good. At present, there are a lot of aluminum alloy monitors on the market. When selection, you must be cautious. Some bracket panel edge areas are very sharp. If you are not careful, you can cut the mobile phone data cable and the outer skin of the display power line. It’s lost.

Each bracket is designed with two large and slightly thick round non -slip foot pads to ensure that the bracket will not shake and shift easily during use. The contact surface of the bracket foot and the desktop is relatively wide, which can further enhance the stability of the bracket during use. Even a large display of more than 32 inches can be used with confidence.

不做低头族,是时候试试这款ORICO高颜值显示器支架了

The height of the bracket foot is about 75mm. For people who prefer neat, the keyboards and mouses can be stored below, making the desktop look cleaner and more neat. However, I prefer to put small objects such as mobile phones, record books, U disks, mobile hard disks, data cables, and mobile phone charging heads under the bracket. In my opinion, these small objects are more difficult to store and easier to storage, easier to storage, and easier Occupy precious desktop space.

不做低头族,是时候试试这款ORICO高颜值显示器支架了

In general, the display bracket of ORICO’s aluminum alloy panel has the characteristics of high value, outstanding texture, and strong support. It can not only easily support all kinds of monitors. At the same time It is also very suitable for the use of laptop computer brackets. If you have the needs of a display stand in the near future, you may wish to try it.

The above is the introduction and description of wood stand teak material monitor stand rising stand with high quality, I hope it can be helpful to you.